POOL PUMP AND MOTOR 0.75kw SPECK BADU PORPOISE

POOL PUMP AND MOTOR 0.75kw SPECK BADU PORPOISE (NEXT GEN) Product Description The SPECK BADU® Porpoise 0.75 kW (Next GEN) is a premium self-priming circulation pump engineered with German precision for medium to larger residential pools. Designed for pools up to 60,000 litres, the unit features an upgraded lid system and enhanced motor efficiency. It’s compatible with a wide range of filtration systems, including UNI, Storm 2-bag sand filters, Aqua Max / Aqua Flo, EartheCo, SPECK, QUALITY, Ultra Zap 3-bag sand filters, and the Badu Ecowise 3 cartridge filter. Its versatility allows for either above-ground or below-ground installation, so long as the mounting surface is flat and remains dry. For optimal performance and warranty compliance, professional installation by a certified electrician or pool technician is strongly recommended. During plumbing setup, the suction and discharge lines must never be smaller than 50 mm (63 mm is recommended). The pump operates best when placed no more than ± 300 mm above the pool water level, and a clearance of at least 150 mm behind the motor ensures airflow and cooling. Flood protection and proper drainage in the pump house are essential to prevent motor damage. The motor is fan cooled, requiring sufficient ventilation during operation. Electrical wiring must comply with safety standards and a suitable cable must replace the test cable provided. The unit ships preconfigured for clockwise rotation (viewed from motor end). For maintenance, regular cleaning of the leaf trap, annual replacement of the lid O-ring, filter backwashing, and avoiding dry operation or blocked valves are key. Fault diagnostics typically focus on wiring, seal failure, rotation, and impeller obstruction. This model includes a 36-month factory warranty, valid only if the manual’s installation and operational instructions are strictly followed. FAQ;s  What pool size is the 0.75 kW Porpoise pump suited for?It is ideal for pools with capacities up to 60,000 litres. Which filters work with this pump in South Africa?It is compatible with UNI, Storm 2-bag filters, Aqua Max / Aqua Flo, EartheCo, SPECK, QUALITY, Ultra Zap 3-bag filters, and Badu Ecowise 3 cartridge filters. Can this pump be installed below ground level?Yes — above or below ground installation is possible, provided the base is stable and protected from flooding. What pipe sizes are required for suction and discharge?Minimum 50 mm diameter is required; 63 mm is recommended for improved flow. How high above water level can the pump be installed?It should not exceed ± 300 mm above the pool water level. Why is motor clearance important?At least 150 mm of clearance behind the motor is needed for cooling airflow and maintenance access. Does flood damage affect the warranty?Yes — any damage caused by flooding or water ingress will void the warranty. Key Features & Benefits Designed for pools up to 60,000 L Compatible with multiple 3-bag sand and cartridge filters German engineering ensures efficiency and reliability Improved lid design for easier servicing Supports both above and below ground installations Built for longevity with recyclable components Backed by 36-month factory warranty Technical Specifications Power Output (P₂): 0.75 kW Power Input (P₁): 0.67 kW Voltage: 1 – 230 V Inlet / Outlet Connection: 50 / 40 mm Pipe Size (recommended): 50 / 50 mm PVC Rated Current: 3.10 A Motor Speed: ~ 2840 rpm Max Water Temperature: 60 °C Max Casing Pressure: 2.5 bar Warranty: 36 months Colour: Black Assembled Dimensions: 19.6 × 51.3 × 30 cm Conclusion For homeowners and pool contractors in South Africa seeking a reliable, powerful, and flexible pump for mid-size pools, the SPECK BADU® Porpoise 0.75 kW (Next GEN) is a compelling choice. Its compatibility with industry-standard filters, advanced lid system, and German engineering deliver long-term performance. When installed properly and maintained, it offers worry-free circulation and exceptional value over its lifetime. Choose this pump for a balance of strength, durability, and peace of mind. PRODUCT INFORMATION TECHNICAL INFORMATION INSTALLATION INSTRUCTIONS We recommend that the pump is installed by a qualified pool professional or electrician. A good installation of your pool pump will result in many years of trouble-free operation. Careful attention must be paid to the following: 1. Piping: The suction and discharge pipes must not be smaller in diameter than the pump connection i.e., Suction pipe diameter 50mm minimum (recommended 63mm), outlet pipe diameter 50mm minimum. Suitable unions should be used on the pump connections or placed in the lines adjacent to the pump connections in case the pump needs to be removed at any time. Do not support the pipework on the pump or vice versa. Make sure all pipe connections are completely water/airtight by using a suitable pipe jointing compound. Keep suction pipe as short as possible and only use pipes that are sufficiently rated to work at a minimum of 4 bar pressure. The suction line should enter the pump straight and horizontally for a length of at least 4 x the diameter of the pipe. The pump is a self-priming pump, which can be installed above or below water level, if you choose to go below, be sure to connect a control valve on your suction pipe between the pool weir/skimmer and the pump, which will prevent your pump being flooded when you open the lid to clean the pump leaf basket. Do not over tighten fittings into the inlet and outlet of the pump. Position pump on a flat level surface not exposed to flooding, as the pump motor is not waterproof. 2. Pump Positioning: (Important for motor cooling): We recommend that the pump be positioned at a level of no more than ± 300mm above your pool water level. Again, we stress the fact to keep the suction line as short as possible. A minimum clearance of 150mm must be allowed behind the motor fan cowling to the nearest obstruction to ensure proper air ventilation and easy access for servicing. The pump house/box must also have provision for adequate drainage facilities. 3. Ventilation: As the electric motor is fan cooled, sufficient ventilation must be allowed at all times during operation. Failure to do this will cause overheating resulting in premature bearing failure and/or motor burnout. If your pump house/box does not have ventilation holes the lid or door should be left open during operation of the pump. 4. Drainage: Flooding of the electric motor is the most common cause of motor failure. It is essential that adequate drainage be provided in the pump house/box. If the motor fails as a result of flooding, then there is no warranty whatsoever irrespective of how the water penetrated the motor. The pump must be protected from rain and flooding. 5. Electric Connections: These must be carried out by suitably qualified people only. Do not change the motor position as it is provided with a drain hole at the bottom to drain off any water which may leak past the mechanical shaft seal. A cable gland must be fitted to the terminal box. NOTE: The length of cable supplied with the pump is for testing only and should be replaced with suitably rated cable. Minimum specification 60245IEC66 (HO7RN-F). 6. Rotation: Before checking the rotation, drain the pump leaf trap of water. The correct rotation is clockwise when viewed from the motor end. Pumps with 220-volt single phase motors are wired at the manufacturer for the correct rotation. How to keep your pool pump in good running condition 1. Clean the leaf trap in the pump and pool weir regularly. 2. Do not allow dust to accumulate on the motor as this affects the cooling process. 3 Do not leave foreign objects lying on the motor. 4 Change the rubber 0-Ring in the lid at 1-year intervals to maintain a good seal. The face on the leaf trap where the 0-Ring sits must be kept clean and smooth. 6. DO NOT RUN THE PUMP DRY or under closed valve conditions for extended periods. 7. Backwash your filter once a week, or when the pressure exceeds 50% above the starting operating pressure. 8. No Vaseline or petroleum-based lubricants should be used for lubricating 0-Rings or seals. Only silicone paste should be used. Troubleshooting a pool pump: Safety first! Isolate the motor before checking for problems. Motor fails to start: A) Check that incoming mains wires are connected to the correct motor terminals. B) Check that the mains supply coming into the motor at the terminals corresponds with the data on the motor name plate. C) Remove the fan cowl of the motor or insert a screwdriver in the slot of the motor shaft at the fan end and check if the shaft can be rotated freely. If this is not the case, the motor will have to be removed to check if foreign objects are jammed in the impeller. D) Reset thermal overload (if fitted) at the reset button on motor terminal box. Motor hums but will not start: A) Remove the fan cowl of the motor or insert a screwdriver in the slot of the motor shaft at the fan end and check if the shaft can be rotated freely. If this is not the case, the motor will have to be removed to check for faulty bearings, or if foreign objects have become jammed in the impeller. If the shaft can be rotated, check that the capacitor is functioning. B) Check that phases of motor windings are not down to earth. If they are the motor has been wet or is burned out. Pump runs but will not pump or pumps poorly. A) Check direction of rotation. B) Make sure pump is properly primed. C) Make sure correct valves are open. D) Make sure that leaf trap and filter are clean. Backwash filter if necessary. E) Make sure that leaf trap lid and “0” Ring are sealing properly, and that lid lock handle is tightened firmly. This can normally be diagnosed by air bubbles entering the pool at return point. Water leaks from drain seal plate flange: The mechanical seal needs to be replaced. Motor runs noisily: A) Clean leaf trap and check for any obstruction on the suction line. B) If this does not help, the motor bearings may need replacement. Warranty